리눅스 tc 명령어로 아웃바운드 트래픽 제어하기
페이지 정보
본문
[code]
#!/bin/bash
#
# tc uses the following units when passed as a parameter.
# kbps: Kilobytes per second
# mbps: Megabytes per second
# kbit: Kilobits per second
# mbit: Megabits per second
# bps: Bytes per second
# Amounts of data can be specified in:
# kb or k: Kilobytes
# mb or m: Megabytes
# mbit: Megabits
# kbit: Kilobits
# To get the byte figure from bits, divide the number by 8 bit
#
TC=/sbin/tc
IF=eth0 # Interface
DNLD=3mbit # DOWNLOAD Limit
UPLD=3mbit # UPLOAD Limit
IP=10.101.0.11 # Host IP
#IP=xxx.xxx.xxx.xxx # Host IP
U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32"
start() {
$TC qdisc add dev $IF root handle 1: htb default 30
$TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD
$TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD
$U32 match ip dst $IP/32 flowid 1:1
$U32 match ip src $IP/32 flowid 1:2
}
stop() {
$TC qdisc del dev $IF root
}
restart() {
stop
sleep 1
start
}
show() {
$TC -s qdisc ls dev $IF
}
case "$1" in
start)
echo -n "Starting bandwidth shaping: "
start
echo "done"
;;
stop)
echo -n "Stopping bandwidth shaping: "
stop
echo "done"
;;
restart)
echo -n "Restarting bandwidth shaping: "
restart
echo "done"
;;
show)
echo "Bandwidth shaping status for $IF:\n"
show
echo ""
;;
*)
pwd=$(pwd)
echo "Usage: $(/usr/bin/dirname $pwd)/tc.bash {start|stop|restart|show}"
;;
esac
exit 0
[/code]
주요 설정 부분은
IF : 랜카드 지정 ex) eth0
DNLD : 다운로드 제한 트래픽
UPLD : 업로드 제한 트래픽
IP : IF에 설정된 IP 주소, VM 일 경우 내부의 IP
실행방법 - 위 스크립트를 tc.sh 로 저장하고 실행권한을 준 후에
# tc.sh start
# tc.sh stop
# tc.sh restart
## 참고
tc 는 서버에서 나가는(outbound) 트래픽만 제한이 가능하고 서버로 들어가는(inbound) 트래픽은 제어하지 않는다.
https://kldp.org/node/59454
https://dejavuqa.tistory.com/307
https://tldp.org/HOWTO/html_single/Traffic-Control-HOWTO/
## 다른 버전의 문서는 아래에 있다.
https://www.baragi.net/bbs/board.php?bo_table=server&wr_id=8592
#!/bin/bash
#
# tc uses the following units when passed as a parameter.
# kbps: Kilobytes per second
# mbps: Megabytes per second
# kbit: Kilobits per second
# mbit: Megabits per second
# bps: Bytes per second
# Amounts of data can be specified in:
# kb or k: Kilobytes
# mb or m: Megabytes
# mbit: Megabits
# kbit: Kilobits
# To get the byte figure from bits, divide the number by 8 bit
#
TC=/sbin/tc
IF=eth0 # Interface
DNLD=3mbit # DOWNLOAD Limit
UPLD=3mbit # UPLOAD Limit
IP=10.101.0.11 # Host IP
#IP=xxx.xxx.xxx.xxx # Host IP
U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32"
start() {
$TC qdisc add dev $IF root handle 1: htb default 30
$TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD
$TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD
$U32 match ip dst $IP/32 flowid 1:1
$U32 match ip src $IP/32 flowid 1:2
}
stop() {
$TC qdisc del dev $IF root
}
restart() {
stop
sleep 1
start
}
show() {
$TC -s qdisc ls dev $IF
}
case "$1" in
start)
echo -n "Starting bandwidth shaping: "
start
echo "done"
;;
stop)
echo -n "Stopping bandwidth shaping: "
stop
echo "done"
;;
restart)
echo -n "Restarting bandwidth shaping: "
restart
echo "done"
;;
show)
echo "Bandwidth shaping status for $IF:\n"
show
echo ""
;;
*)
pwd=$(pwd)
echo "Usage: $(/usr/bin/dirname $pwd)/tc.bash {start|stop|restart|show}"
;;
esac
exit 0
[/code]
주요 설정 부분은
IF : 랜카드 지정 ex) eth0
DNLD : 다운로드 제한 트래픽
UPLD : 업로드 제한 트래픽
IP : IF에 설정된 IP 주소, VM 일 경우 내부의 IP
실행방법 - 위 스크립트를 tc.sh 로 저장하고 실행권한을 준 후에
# tc.sh start
# tc.sh stop
# tc.sh restart
## 참고
tc 는 서버에서 나가는(outbound) 트래픽만 제한이 가능하고 서버로 들어가는(inbound) 트래픽은 제어하지 않는다.
https://kldp.org/node/59454
https://dejavuqa.tistory.com/307
https://tldp.org/HOWTO/html_single/Traffic-Control-HOWTO/
## 다른 버전의 문서는 아래에 있다.
https://www.baragi.net/bbs/board.php?bo_table=server&wr_id=8592
추천0
댓글목록
등록된 댓글이 없습니다.